$ -
Main Features:
【Pre-installed Klipper Firmware】The Neptune 4 Pro 3D printer is designed to be fast and efficient. It features a quiet Klipper motherboard and ARM 64-bit main frequency quad-core processor for sufficient processing power, allowing it to print at a amazing speed of up to 500mm/s (recommended 250mm/s), and supports advanced functions like input shaping and pressure advance to achieve accurate and smooth models.
【Dual-Gear Direct Drive Extruder】The dual-gear direct drive extruder with a 5.2:1 reduction ratio for smooth and consistent extrusion, combined with the copper-titanium bi-metal throat pipe and unique air duct design, improve heat dissipation and reduce nozzle clogging.
【300°C High-temp Nozzle】With a high-temperature nozzle reaching 300°C, the printer can handle a wide range of filaments, including PLA, PETG, ABS, TPU, and high-temperature filaments like nylon. The extended hot end design ensures consistent heating and faster melting and extrusion, resulting in faster printing speed.
【Intelligent Segmented Heatbed】With 100W 150W power output, the slicing software automatically recognizes the size of the model during slicing and activates the peripheral heating zone if the model size exceeds the center heating zone (120mmx120mm). The two partitions can also be turned on and off manually for more precise temperature control. Additionally, the surface of the PEI magnetic platform is marked for guidance.
【Auto Bed Leveling Auxiliary Leveling】With 121 (11x11) points auto bed leveling, you can achieve consistent and reliable prints every time without the need for manual bed leveling. Additionally, the auxiliary leveling by hand-twist knobs allows for further fine-tuning of the print bed’s level for improved print quality.
【Efficient Heat Dissipation】ELEGOO Neptune 4 Pro also features 2 thickened double-sided 4015 ball bearing cooling fans and 4x4020 ball bearing blower fans behind the print head for omnidirectional rapid cooling the newly printed layers to prevent warping and improve overall print quality even at a fast printing speed.
*************************************************************************
*Please help support this channel at NO COST TO YOU. If you shop on* *Amazon, please use this link: *
*I will get a small commission and it costs you nothing. *
*************************************************************************
HEY YOU ABOUT TO POST SOMETHING STUPID:
Yes, I know my hands are large/fat. It’s because of a heart condition I suffer from called Congestive Heart Failure. Here’s a link to some information about CHF:
One of the symptoms is that it causes fluid retention, mostly in the hands, feet/ankles, and face..
-------------------------------------------------------------------------------------------------------------------
Support learnelectronics:
Amazon Store:
If you are shopping for electronic components, test gear or consumables please consider visiting my Amazon shop @
Patreon:
Please check out and pledge a dollar if you can. It will go a long way to keeping the channel alive. It costs a bit of money to buy all the items and produce these videos. Your help is appreciated.
Paypal:
you’d like to send a one-time donation you can use this link:
---------------------------------------------------------------------------------------------------------------------
Gear I use:
Multimeter: OWON B33
Oscilloscope: KIPRIM DS1202
Signal generator: Junctek JDS8080
Component Tester: T7 Multifunction
Soldering Station: Sealody ???????
2 views
0
0
7 years ago 00:01:53 363
Introducing the Cemtrex SmartDesk
2 years ago 00:04:17 121
Introducing the Scopeswitch
12 years ago 00:03:02 3.9K
Introducing the iPhone 5S
10 years ago 00:04:01 662
Introducing the DJI Osmo
12 years ago 00:08:13 76
Introducing The Back Lever
9 years ago 00:02:17 614
Introducing the Demo 8 Alloy
11 years ago 00:02:56 442
Introducing the iWatch
12 years ago 00:01:15 456
Introducing... The Homer!
13 years ago 00:01:12 1.7K
Introducing the Leap
10 years ago 00:02:09 490
GoPro: Introducing The Jam
5 years ago 00:02:29 50
Introducing The Cat LuLu
5 years ago 00:02:49 101
Introducing the Moraharpa
8 years ago 00:01:43 237
Introducing The Vessel
10 years ago 00:01:01 160
Introducing the Stumpjumper FSR
10 years ago 00:02:07 634
GoPro: Introducing The Strap
11 years ago 00:03:06 1K
Hay Day: Introducing the Bees
9 years ago 00:00:59 402
Introducing the FLIR Scout TK
9 years ago 00:01:35 91
Introducing the Octobot
12 years ago 00:01:04 460
Introducing the Domino’s DomiCopter!
11 years ago 00:02:06 255
Introducing the iWatch 2014
12 years ago 00:01:50 561
Playstation 4 ’Introducing The PlayRoom’
2 years ago 00:03:14 46.6K
Free The Carve | Introducing The New Freecarver Series